Common Specs & Procedures
SANTA CRUZ COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATIONS | ||
| Torque | Torque values are in the text of the AIR CONDITIONING SYSTEM article. Also refer to TIGHTENING TORQUES . | ||
| Axle Nut/Hub Nut | |||
| Front | 294.2-313.8 N.m (30.0-32.0 kgf/m, 217.0-231.5 lb. ft.) | ||
| Rear | 294.2-313.8 N.m (30.0-32.0 kgf/m, 217.0-231.5 lb. ft.) | ||
| Battery | |||
| 2.5L | BATTERY | ||
| 2.5L Turbo | BATTERY | ||
| Brakes | |||
| Bleeding Sequence | BRAKE BLEEDING PROCEDURES | ||
| Disc Brakes | |||
| Service Specifications | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUES | ||
| Charging | |||
| Generator | |||
| 2.5L | ALTERNATOR | ||
| 2.5L Turbo | ALTERNATOR | ||
| Alternator Bolt Torque | |||
| 2.5L, 2.5L Turbo | 49.0 - 63.7 N.m (5.0 - 6.5 kgf.m, 36.2 - 47.0 lb-ft) | ||
| Drive Belts | |||
| Adjustment |
2.5L, 2.5L Turbo - Self-tensioning drive belt tensioner |
||
| Routing | |||
| 2.5L | Refer to "Engine Drive Belt Routing Diagram" figure under INSTALLATION | ||
| 2.5L Turbo | Refer to "Engine Drive Belt Routing Diagram" figure under INSTALLATION | ||
| Engine Cooling | |||
| General Service Specifications | |||
| 2.5L | See Cooling System in table under SPECIFICATIONS . | ||
| 2.5L Turbo | See Cooling System in table under SPECIFICATIONS . | ||
| Radiator Cap Pressure | 93.16-122.58 kPa (0.95-1.25 kgf/cm2 , 13.51-17.78 psi) | ||
| Thermostat R & I | |||
| 2.5L | INTEGRATED THERMAL MANAGEMENT MODULE (ITM) | ||
| 2.5L Turbo | INTEGRATED THERMAL MANAGEMENT MODULE (ITM) | ||
| Water Pump R & I | |||
| 2.5L | WATER PUMP | ||
| 2.5L Turbo | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | |||
| 2.5L | COMPRESSION PRESSURE INSPECTION | ||
| 2.5L Turbo | COMPRESSION PRESSURE INSPECTION | ||
| Oil Pressure | |||
| 2.5L, 2.5L Turbo | 90.22 kPa (0.92 kgf/cm2 , 13.09 psi) or above at 1000 RPM | ||
| Overhaul | |||
| 2.5L | SPECIFICATIONS | ||
| 2.5L Turbo | SPECIFICATIONS | ||
| Torque | |||
| 2.5L | TIGHTENING TORQUES . | ||
| 2.5L Turbo | TIGHTENING TORQUES . | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque 2.5L, 2.5L Turbo | 94.0-101.3 ft. lbs. (127.5-137.3 N.m) | ||
| Fuel System | |||
| Pressure Specification | |||
| 2.5L, 2.5L Turbo | 480-520 kPa (4.9-5.3 kgf/cm2 , 69.6-75.4 psi) | ||
| Fuel Pressure Test Procedure | |||
| 2.5L | FUEL PRESSURE TEST | ||
| 2.5L Turbo | FUEL PRESSURE TEST | ||
| Fuel Filter R & I | |||
| 2.5L | FUEL FILTER | ||
| 2.5L Turbo | FUEL FILTER | ||
| Ignition | |||
| Firing Order & Cylinder Identification | 1-3-4-2: Also see FIRING ORDER & CYLINDER IDENTIFICATION article. | ||
| Ignition Wires (Resistance) | |||
| 2.5L, 2.5L Turbo | Coil On Plug | ||
| Ignition Wires (Routing) | |||
| 2.5L, 2.5L Turbo | Coil On Plug | ||
| Spark Plug | |||
| Type | |||
| 2.5L | SILZKR7K11S | ||
| Gap | 0.0394-0.0433 in. (1.0-1.1 mm) | ||
| Torque | 14.7-24.5 N.m (1.5-2.5 kgf/m, 10.8-18.0 lb. ft.) | ||
| 2.5L Turbo | SILZKR8J9GS | ||
| Gap | 0.0315-0.0354 in. (0.8-0.9 mm) | ||
| Torque | 14.7-24.5 N.m (1.5-2.5 kgf/m, 10.8-18.0 lb. ft.) | ||
| Starting | |||
| Starter | |||
| 2.5L | STARTER | ||
| Torque | 49.0-63.7 N.m (36.2-47.0 ft. lbs.) | ||
| 2.5L Turbo | STARTER | ||
| Torque | 49.0-63.7 N.m (36.2-47.0 ft. lbs.) | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT | ||
| Torque | TIGHTENING TORQUE | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 107.9-125.5 N.m (11.0-13.0 kgf/m, 79.6-94.0 lb. ft.) | ||