LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Hummer >> 2006 >> H3 Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 6 (Computer/Integrating Systems) >> Diagnostic Information and Procedures >> Retained Accessory Power (RAP) Inoperative
September 30: LEMON manuals is back up on a temporary server! Slowness is possible

Retained Accessory Power (RAP) Inoperative

WARNING: This page is about a different car, the 2005 GMC Canyon and 2005 Chevrolet Colorado. However, it is still accessible from the selected car via links, so may be relevant.
Retained Accessory Power (RAP) Inoperative

Step Action Yes No
Schematic Reference: Retained Accessory Power (RAP) Schematics 
Connector End View Reference: Master Electrical Component List in Wiring Systems
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2 Do only the power windows and wipers exhibit this symptom? Go to Step 5  Go to Step 3 
3
  1. Observe the following parameters in body control module (BCM) data list:
    • Driver Door Ajar Sw.
    • Passenger Door Ajar Sw.
  2. Open and close each door while observing the respective parameter.
Does the scan tool display change from Ajar to Door Closed respectively?		 Go to Step 4  Go to Symptoms - Lighting Systems in Lighting Systems
4
  1. Select diagnostic circuit check and then class 2 power mode, on the scan tool.
  2. Close all of the doors.
  3. Turn ON the ignition, with the engine OFF.
  4. Wait 5 seconds then turn the ignition OFF.
  5. Wait the time-out for retained accessory power (RAP).
Did the scan tool display the RAP power mode then time-out, and display Off-Awake power mode?		 Go to Step 5  Go to Step 11 
5
  1. Turn OFF the ignition.
  2. Disconnect the RAP relay.
  3. Turn ON the ignition, with the engine OFF.
  4. With a test lamp that is connected to a good ground, probe the battery positive voltage circuit of the RAP relay.
Does the test lamp illuminate?		 Go to Step 6  Go to Step 9 
6
  1. Connect a fused wire jumper across the relay switch circuits of the RAP relay.
  2. Turn the ignition ON, with the engine OFF.
  3. Attempt to operate the power windows and wipers.
Do the power windows and wipers operate normally?		 Go to Step 8  Go to Step 7 
7 Repair the supply voltage circuit to power windows and wipers. Refer to Wiring Repairs in Wiring Systems.
Did you complete the replacement?		 Go to Step 13  -
8 Inspect for poor connections at the RAP relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 13  Go to Step 10 
9 Repair the RAP relay supply voltage circuit for a short to ground or an open.
Did you find and correct the condition?		 Go to Step 13  -
10 Replace the RAP relay.
Did you complete the replacement?		 Go to Step 13  -
11 Inspect for poor connections at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 13  Go to Step 12 
12 Replace the BCM. Refer to Control Module References  for replacement, setup, and programming.
Did you complete the procedure?		 Go to Step 13  -
13 Operate the system in order to verify the repair.
Did you correct the condition?		 System OK Go to Step 1 
scientia non olet · About LEMON Manuals