LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> GMC >> 2024 >> Hummer EV 2 >> Repair and Diagnosis >> Accessories & Equipment >> Cruise Control Systems >> Repair Instructions >> Cruise Control Switch Replacement >> Removal Procedure
July 1: So it begins. Don't worry, this is not in the correct legal jurisdiction!

Removal Procedure

  1. Disable the SIR system. SIR Disabling and Enabling
  2. GM5810457Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    Left side shown, right side similar.

    Use a flat bladed plastic trim tool to depress the steering wheel airbag access hole cover detents to remove the left and right steering wheel airbag access hole covers (1).

  3. GM5810539Courtesy of GENERAL MOTORS COMPANY

    Steering Wheel Airbag Bolt (1) - Remove [2x]

  4. Release the connector position assurance (CPA) retainer.
  5. Disconnect the electrical connectors. (3)
  6. Steering Wheel Airbag (2) - Remove
  7. GM5810855Courtesy of GENERAL MOTORS COMPANY
    CAUTION:

    During steering wheel bolt removal, observe the following precautions:

    • Do NOT use heat on the steering wheel bolt, steering wheel, or steering column. Using heat could cause damage to the steering related components.
    • Do NOT hammer or apply excessive downward force on the steering wheel bolt, steering wheel, or steering column. Hammering or applying excessive downward force could cause damage to the steering related components.
    NOTE:
    • Steering wheel bolts installed during manufacturing require high torque efforts to remove.
    • The ONLY acceptable bit for removing and installing the steering wheel bolt is a T50 Torx bit. Do NOT use any other size bit or a worn bit.
    • If a power tool is used to remove the steering wheel bolt, the tool must have a minimum torque rating greater than 75 N.m (55 lb ft) and both the power tool and the T50 Torx bit MUST be positioned perpendicular to the bolt recess.
    • Apply appropriate downward force to maintain engagement of bit to bolt recess during bolt removal.

    Loosen the steering wheel bolt (1) until 2 to 3 threads are still engaged.

  8. Wiggle the steering wheel until the wheel disengages completely.
  9. Steering Wheel Bolt (1) - Remove
  10. GM5810856Courtesy of GENERAL MOTORS COMPANY

    Disconnect the electrical connector.

  11. Steering Wheel (1) - Remove
  12. GM5891030Courtesy of GENERAL MOTORS COMPANY

    Steering Wheel Spoke Cover Bolt (1) - Remove [4x]

  13. Steering Wheel Bolt (2) @ Steering Wheel Shroud - Remove [4x]
  14. GM5891033Courtesy of GENERAL MOTORS COMPANY

    Steering Wheel Shroud (1) - Remove

  15. GM5892053Courtesy of GENERAL MOTORS COMPANY

    Disconnect the electrical connector.

  16. Radio Volume Switch (1) - Remove
  17. GM5892331Courtesy of GENERAL MOTORS COMPANY

    Disconnect the electrical connector.

  18. Radio Favorites Switch (1) - Remove
  19. GM5892333Courtesy of GENERAL MOTORS COMPANY

    Steering Wheel Spoke Cover Bolt (1) - Remove [2x]

  20. GM6087924Courtesy of GENERAL MOTORS COMPANY

    Disconnect the electrical connectors. (1)

  21. GM6087928Courtesy of GENERAL MOTORS COMPANY

    Remove the driver monitoring module (1) by unclipping the retainer clips and sliding away from the spoke cover.

  22. GM5892334Courtesy of GENERAL MOTORS COMPANY

    Disconnect the electrical connectors.

  23. Steering Wheel Trim Spoke Cover Applique (1) - Remove
  24. GM5892336Courtesy of GENERAL MOTORS COMPANY

    Steering Wheel Bolt (1) @ Cruise Control Switch - Remove [3x]

  25. Cruise Control Switch (2) - Remove
scientia non olet · About LEMON Manuals