Installation Procedure

WARNING: This page is about a different car, the 2020 Cadillac CT4. However, it is still accessible from the selected car via links, so may be relevant.

Courtesy of GENERAL MOTORS COMPANY

Brake System Control Module (1) - Install
Courtesy of GENERAL MOTORS COMPANY

CAUTION:
Refer to Fastener Caution .

Electronic Brake Control Module Bolt (1) - Install NEW and tighten [ 4x ] Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Electrical Connector (1)@Brake System Control Module - Connect
Courtesy of GENERAL MOTORS COMPANY

Front End Sheet Metal Diagonal Brace (2) - Install
Front End Sheet Metal Diagonal Brace Bolt (3) - Install and tighten [ 2x ] - Fastener Specifications
Front End Sheet Metal Diagonal Brace Nut (1) - Install and tighten - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Plenum Front Panel (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Install the forward lamp wiring harness extension (3) into the plenum front panel.
Plenum Front Panel Bolt (1) - Install and tighten [ 4x ] - Fastener Specifications
Plenum Front Panel Nut (2) - Install and tighten [ 3x ] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Install the forward lamp wiring harness extension (3) into the plenum front panel.
Plenum Front Panel Nut (1) - Install and tighten [ 3x ] - Fastener Specifications
Plenum Front Panel Bolt (2) - Install and tighten [ 3x ] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

Install the windshield wiper system module (2) in the vehicle.
Windshield Wiper System Module Bolt (1) - Install and tighten [ 2x ] - Fastener Specifications
Connect the windshield wiper motor electrical connector.
Courtesy of GENERAL MOTORS COMPANY

Windshield Wiper System Module Shield (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Air Inlet Grille Panel (2) - Install
Install the air inlet grille panel (2) between both hood hinges.
Connect the windshield washer nozzle hose to the windshield washer pump hose.
Air Inlet Grille Panel Retainer (1) - Install [ 6x ]
Courtesy of GENERAL MOTORS COMPANY

Install the front compartment side sight shields (2) to both sides.
Install the front compartment side sight shield retainers (1) to both sides.
Courtesy of GENERAL MOTORS COMPANY

Install the hood rear outer air inlet seals (2) to both sides.
Install the hood rear outer air inlet seal retainers (1) to both sides.
Courtesy of GENERAL MOTORS COMPANY

Install the air inlet grille panel extensions (1).
Remove the masking tape from the body around the top edges of the air inlet grille panel extensions (1).
Using a 50/50 mixture of isopropyl alcohol and clean drinkable water with a clean towel, remove any left over adhesive residue from the masking tape.
Courtesy of GENERAL MOTORS COMPANY
Clean the windshield wiper transmission pivot shaft splines with a soft wire brush before installing the windshield wiper arms (3).
Position the windshield wiper arms (3) on the windshield wiper transmission pivot shafts.
Windshield Wiper Arm Nut (2) - Install and tighten [ 2x ] - Fastener Specifications
Windshield Wiper Arm Finish Cap (1) - Install [ 2x ]
Connect the battery negative cable. Battery Negative Cable Disconnection and Connection
Reprogram the brake system control module. Control Module References
Courtesy of GENERAL MOTORS COMPANY

If required, realign the windshield wipers to their respective alignment circles (1) on the windshield.
Lubricate the windshield with clean washer fluid.
Run the windshield wipers for two complete cycles then turn off the windshield wipers.
Ensure the windshield wipers are in the full park position.
Inspect the windshield wipers for proper position to the alignment circles (1) on the windshield.