Section 27 (5-Speed Automatic Transmission 01V - Internal Components, Servicing)
WARNING: This page is about a different car, the 2005 Audi A4, 2004 Audi A4, 2003 Audi A4, and 2002 Audi A4. However, it is still accessible from the selected car via links, so may be relevant.
- 00 - General, Technical Data
- 32 - Torque converter
- 37 - Automatic Transmission - Controls, Housing
- Transmission, attaching assembly stand
- Planetary gear, disassembling and assembling
- Tower I , disassembling and assembling
- Tower "I" , disassembling and assembling
- Tower "I" , component overview
- Tower "I" , disassembling
- Clutch "F" , component overview
- Clutch "F" , disassembling and assembling
- Clutch "D/G" with freewheel, component overview
- Clutch "D/G" with freewheel, disassembling and assembling
- Planetary drive "III" , component overview
- Planetary drive "III" , disassembling and assembling
- Tower "I" , assembling
- Tower II , disassembling and assembling
- Tower "II" , disassembling and assembling
- Tower "II" , component overview
- Tower "II" , disassembling
- Clutch "B" , component overview
- Clutch "B" , disassembling and assembling
- Clutch "A" , component overview
- Clutch "A" , disassembling and assembling
- Clutch "E" , component overview
- Clutch "E" , disassembling and assembling
- Tower "II" , assembling
- Clutch C , disassembling and assembling
- 38 - Automatic Transmission - Gears, Hydraulic controls
- ATF pump, disassembling and assembling
- ATF pump, disassembling and assembling
- ATF pump, component overview
- ATF pump (with assembled transmission), completely removing and installing
- ATF pump and ATF supply housing, removing and installing
- ATF supply housing with stator shaft, removing and installing
- Stator shaft, removing and installing
- ATF pump shaft seal, replacing
- Installed transmission, servicing
- Installed transmission, servicing
- Valve body, removing and installing
- Inner oil line, removing and installing
- Transmission Vehicle Speed Sensor (VSS) G38/Transmission Output Speed (RPM) Sensor G195 , removing and installing
- Transmission Input Speed (RPM) Sensor G182 (transmission with hydraulic control "E17"), removing and installing
- Transmission Input Speed (RPM) Sensor G182 (transmission with hydraulic control "E18/2"), removing and installing
- Wiring harness in transmission, removing and installing
- Evaluating wear on transmission components
- Evaluating wear by evaluating ATF color and impurities
- Clutch "F"
- Clutch "D/G" with freewheel
- Planetary drive "III"
- Clutch "B"
- Clutch "A"
- Clutch "E"
- Clutch "C"
- ATF supply
- Notes
- Checking brass sleeve of ATF pump housing for wear
- Checking components of ATF pump for grooves and signs of wear
- Check yoke in ATF pump wheel
- Checking volume controlling valve in ATF pump
- Checking brass sleeves of stator shaft for wear
- Checking rectangular rings item - 16 - for wear
- Checking rectangular ring item - 17 - for wear
- ATF pump, disassembling and assembling
- 39 - Final drive, Differential
- Front final drive and transfer case, servicing
- Front final drive and transfer case, servicing
- Transfer case with Torsen differential, removing and installing
- Front final drive and transfer case, component overview
- Driveshaft output flange shaft seal, replacing
- Shaft seal in front final drive intermediate flange, replacing
- Shaft seal in drive pinion, replacing
- Needle bearing for spur gear 2, replacing
- Front final drive and transfer case, servicing