LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Volkswagen >> 2000 >> New Beetle GLX, Standard >> Repair and Diagnosis >> Engine Performance >> System >> On Board Diagnostic - Brake System (Hatchback) >> 01 On Board Diagnostic >> Diagnosis And Testing >> DTC Table
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC Table

Note

Example:  
DTC Malfunction code
5 digit 3 digit
00283 035
VAG 1551 print-out Possible cause Corrective action
00283    
Left Front ABS Wheel Speed Sensor -G47-
  • Open circuit, short to positive or Ground, or loose contact in connections between Left Front ABS Wheel Speed Sensor -G47- and ABS Control Module J104 (w/EDL).
 -- Check wiring and connections using wiring diagram-- Perform electrical checks ELECTRICAL TESTING 
 
  • Damaged rotor or Left Front ABS Wheel Speed Sensor -G47-
  • Speed sensor windings Left Front ABS Wheel Speed Sensor -G47- faulty
 -- Check Left Front ABS Wheel Speed Sensor -G47- and rotor for damage-- Replace Left Front ABS Wheel Speed Sensor -G47-
    Removal and Installation
    If the malfunction occurs again:
 
  • ABS Control Module J104 (w/EDL) faulty
 -- Replace ABS Control Module J104 (w/EDL)
    Removal and Installation
VAG 1551 print-out Possible cause Corrective action
00283    
Front left speed sensor Left Front ABS Wheel Speed Sensor -G47- Signal outside tolerances(1)
  • Open circuit, short to positive or Ground, or loose contact in connections between Left Front ABS Wheel Speed Sensor -G47- and ABS Control Module J104 (w/EDL)
 -- Check wiring and connections using wiring diagram-- Perform electrical checks ELECTRICAL TESTING 
 
  • Electrical interference from other sources (high frequency radiation e.g. non-insulated ignition cable)
 -- Read measured value block FUNCTION 08 - READING MEASURED VALUE BLOCK  Display group number 001
 
  • Damaged rotor or Left Front ABS Wheel Speed Sensor -G47-
  
 
  • Excessive air gap between Left Front ABS Wheel Speed Sensor -G47- and rotor (signal not OK.)
 -- Check Left Front ABS Wheel Speed Sensor -G47- and rotor for damage-- Replace rotor/speed sensor
    Removal and Installation
(1) Type of DTC, this DTC is only recognized above 20 km/h (13 MPH) (carry out test drive).
VAG 1551 print-out Possible cause Corrective action
00283    
Left Front ABS Wheel Speed Sensor -G47- Mechanical malfunction(1)
  • Excessive air gap between Left Front ABS Wheel Speed Sensor -G47- and rotor (signal not OK.)
 -- Check installation of Left Front ABS Wheel Speed Sensor -G47- and rotor Removal and Installation -- Read measured value block FUNCTION 08 - READING MEASURED VALUE BLOCK  Display group number 002-- Perform output Diagnostic Test Mode (DTM) FUNCTION 03 - OUTPUT DIAGNOSTIC TEST MODE 
    If the malfunction occurs again:
 
  • Outlet valve in ABS Hydraulic Unit -N55- faulty
 -- Replace ABS Hydraulic Unit -N55-
    Removal and Installation
(1) Type of DTC, this DTC is only recognized above 20 km/h (13 MPH) (carry out test drive).
VAG1551 Scan Tool display Possible cause Corrective action
00000    
No DTC recognized If "No DTC recognized" appears after carrying out repairs, On Board Diagnostic (OBD) is ended.
  If, despite "No DTC recognized" appearing on the display, ABS system does not operate properly, proceed as follows:
  -- Road test at speed exceeding 20 km/h (13 mph).
  -- If there is still no DTC stored, check DTC memory again.
  -- Continue troubleshooting without On Board Diagnostic (OBD) and perform the complete Electrical testing ELECTRICAL TESTING .
VAG 1551 print-out Possible cause Corrective action
00285    
Right Front ABS Wheel Speed Sensor -G45-
  • Open circuit, short to positive or Ground, or loose contact in connections between Right Front ABS Wheel Speed Sensor -G45- and ABS Control Module -J104- (w/EDL)
 -- Check wiring and connections using wiring diagram-- Perform electrical checks ELECTRICAL TESTING 
 
  • Damaged rotor or Right Front ABS Wheel Speed Sensor -G45-
  • Right Front ABS Wheel Speed Sensor -G45- faulty
 -- Check Right Front ABS Wheel Speed Sensor -G45- and rotor for damage-- Replace Right Front ABS Wheel Speed Sensor -G45-
    Removal and Installation
    If the malfunction occurs again:
 
  • ABS Control Module -J104- (w/EDL) faulty
 -- Replace ABS Control Module -J104- (w/EDL)
    Mark 20 Removal and Installation
VAG 1551 print-out Possible cause Corrective action
00285    
Right Front ABS Wheel Speed Sensor -G45- Signal outside tolerances(1)
  • Open circuit, short to positive or Ground, or loose contact in connections between Right Front ABS Wheel Speed Sensor -G45- and ABS Control Module -J104- (w/EDL)
 -- Check wiring and connections using wiring diagram-- Perform electrical checks ELECTRICAL TESTING 
 
  • Electrical interference from other sources (high frequency radiation e.g. non-insulated ignition cable)
 -- Read measured value block FUNCTION 08 - READING MEASURED VALUE BLOCK  Display group number 001
 
  • Damaged rotor or Right Front ABS Wheel Speed Sensor -G45-
  
 
  • Excessive air gap between Right Front ABS Wheel Speed Sensor -G45- and rotor (signal not OK)
 -- Check Right Front ABS Wheel Speed Sensor -G45- and rotor for damage-- Replace rotor/speed sensor
    Removal and Installation
(1) Type of DTC, this DTC is only recognized above 20 km/h (13 MPH) (carry out test drive).
VAG 1551 print-out Possible cause Corrective action
00285    
Right Front ABS Wheel Speed Sensor -G45- Mechanical malfunction(1)
  • Excessive air gap between Right Front ABS Wheel Speed Sensor -G45- and rotor (signal not OK.)
 -- Check installation of Right Front ABS Wheel Speed Sensor -G45- and rotor Removal and Installation -- Read measured value block FUNCTION 08 - READING MEASURED VALUE BLOCK  Display group number 002-- Perform output Diagnostic Test Mode (DTM) FUNCTION 03 - OUTPUT DIAGNOSTIC TEST MODE 
    If the malfunction occurs again:
 
  • Outlet valve in ABS Hydraulic Unit -N55- faulty
 -- Replace ABS Hydraulic Unit -N55-
    Removal and Installation
(1) Type of DTC, this DTC is only recognized above 20 km/h (13 MPH) (carry out test drive).
VAG 1551 print-out Possible cause Corrective action
00287    
Right Rear ABS Wheel Speed Sensor -G44-
  • Open circuit, short to positive or Ground, or loose contact in connections between Right Rear ABS Wheel Speed Sensor -G44- and ABS control module (w/EDL) -J104-
 -- Check wiring and connections using wiring diagram-- Perform electrical checks ELECTRICAL TESTING 
 
  • Damaged rotor or Right Rear ABS Wheel Speed Sensor -G44-
  • Right Rear ABS Wheel Speed Sensor -G44- faulty
 -- Check Right Rear ABS Wheel Speed Sensor -G44- and rotor for damage-- Replace Right Rear ABS Wheel Speed Sensor -G44-
    Removal and Installation
    If the malfunction occurs again:
 
  • ABS Control Module -J104- (w/EDL) faulty
 -- Replace ABS Control Module -J104- (w/EDL)
    Mark 20 Removal and Installation
VAG 1551 print-out Possible cause Corrective action
00287    
Right Rear ABS Wheel Speed Sensor -G44- Signal outside tolerances(1)
  • Open circuit, short to positive or Ground, or loose contact in connections between Right Rear ABS Wheel Speed Sensor -G44- and ABS Control Module -J104- (w/EDL)
 -- Check wiring and connections using wiring diagram-- Perform electrical checks ELECTRICAL TESTING 
 
  • Electrical interference from other sources (high frequency radiation e.g. non-insulated ignition cable)
 -- Read measured value block FUNCTION 08 - READING MEASURED VALUE BLOCK  Display group number 001
 
  • Damaged rotor or Right Rear ABS Wheel Speed Sensor -G44-
  
 
  • Excessive air gap between Right Rear ABS Wheel Speed Sensor -G44- and rotor (signal not OK.)
 -- Check Right Rear ABS Wheel Speed Sensor -G44- and rotor for damage-- Replace rotor/speed sensor
    Removal and Installation
(1) Type of DTC, this DTC is only recognized above 20 km/h (13 MPH) (carry out test drive).
VAG 1551 print-out Possible cause Corrective action
00287    
Right Rear ABS Wheel Speed Sensor -G44- Mechanical malfunction(1)
  • Excessive air gap between Right Rear ABS Wheel Speed Sensor -G44- and rotor (signal not OK.)
 -- Check installation of Right Rear ABS Wheel Speed Sensor -G44- and rotor Removal and Installation -- Read measured value block FUNCTION 08 - READING MEASURED VALUE BLOCK  Display group number 002-- Perform output Diagnostic Test Mode (DTM) FUNCTION 03 - OUTPUT DIAGNOSTIC TEST MODE 
    If the malfunction occurs again:
 
  • Outlet valve in ABS hydraulic unit ABS Control Module -J104- faulty
 -- Replace ABS Hydraulic Unit -N55-
    Removal and Installation
(1) Type of DTC, this DTC is only recognized above 20 km/h (13 MPH) (carry out test drive).
VAG 1551 print-out Possible cause Corrective action
00290    
Left Rear ABS Wheel Speed Sensor -G46- (1) Fault in electrical circuit
  • Open circuit, short to positive or Ground, or loose contact in connections between Left Rear ABS Wheel Speed Sensor -G46- and ABS Control Module -J104- (w/EDL)
 -- Check wiring and connections using wiring diagram-- Perform electrical checks ELECTRICAL TESTING 
 
  • Left Rear ABS Wheel Speed Sensor -G46- windings faulty
  • Damaged rotor or Left Rear ABS Wheel Speed Sensor -G46-
 -- Check Left Rear ABS Wheel Speed Sensor -G46- and rotor for damage-- Replace rotor or Left Rear ABS Wheel Speed Sensor -G46-
    Removal and Installation
    If the malfunction occurs again:
 
  • ABS Control Module -J104- (w/EDL) faulty
 -- ABS Control Module -J104- (w/EDL)
    Mark 20 Removal and Installation
(1) This fault is recognized when vehicle is stationary.
VAG 1551 print-out Possible cause Corrective action
00290    
Left Rear ABS Wheel Speed Sensor -G46- Signal outside tolerances(1)
  • Open circuit, short to positive or Ground, or loose contact in connections between Left Rear ABS Wheel Speed Sensor -G46- and ABS Control Module -J104- (w/EDL)
 -- Check wiring and connections using wiring diagram-- Perform electrical checks ELECTRICAL TESTING 
 
  • Electrical interference from other sources (high frequency radiation e.g. non-insulated ignition cable)
 -- Read measured value block FUNCTION 08 - READING MEASURED VALUE BLOCK  Display group number 001
 
  • Damaged Left Rear ABS Wheel Speed Sensor -G46-
  
 
  • Excessive air gap between Left Rear ABS Wheel Speed Sensor -G46- and rotor (signal not OK.)
 -- Check Left Rear ABS Wheel Speed Sensor -G46- and rotor for damage-- Replace rotor/speed sensor
    Removal and Installation
(1) Type of DTC; this DTC is only recognized above 20 km/h (13 MPH) (carry out test drive).
VAG 1551 print-out Possible cause Corrective action
00290    
Left Rear ABS Wheel Speed Sensor -G46- Mechanical malfunction(1)
  • Excessive air gap between Left Rear ABS Wheel Speed Sensor -G46- and rotor (signal not OK.)
 -- Check installation of Left Rear ABS Wheel Speed Sensor -G46- and rotor Removal and Installation -- Read measured value block FUNCTION 08 - READING MEASURED VALUE BLOCK  Display group number 002-- Perform output Diagnostic Test Mode (DTM) FUNCTION 03 - OUTPUT DIAGNOSTIC TEST MODE 
    If the malfunction occurs again:
 
  • Outlet valve in ABS Hydraulic Unit -N55- faulty
 -- Replace ABS Hydraulic Unit -N55-
    Removal and Installation
(1) Type of DTC; this DTC is only recognized above 20 km/h (13 MPH) (carry out test drive).
VAG 1551 print-out Possible cause Corrective action
00668    
Battery Positive Voltage (B+) Term. 30 Signal outside tolerances
  • Malfunctioning voltage supply wires, connections, Fuse 6 - terminal 30 (on battery fuse panel) S178 and Fuse 7 - terminal 30 (on battery fuse panel) -S179-
 -- Check fuses, wires, connections as well as the voltage supply to control module.-- Check wiring in wiring harness → test step no. 2, ELECTRICAL TEST TABLE => , Electrical testing. For MY 1998: -- Check Ground No. 45 per wiring diagram.
01044    
Control Module incorrectly coded
  • Incorrect code number was entered using Scan Tool VAG1551
  • Open or short circuit in wiring harness connector from terminal 3 to terminal 14.
 -- Check control module coding FUNCTION 07 - CODING CONTROL MODULE .-- Check wiring in wiring harness → test step no. 13, ELECTRICAL TEST TABLE => Functional check: ABS Hydraulic Pump -V64- , Electrical testing.
VAG 1551 print-out Possible cause Corrective action
01130    
ABS operation Implausible signal(1)
  • Electrical interference from other sources (high frequency radiation e.g. non-insulated ignition cable)
 -- Erase DTC memory-- Perform test drive at more than 20 km/h (13 MPH)-- Check DTC memory again
 
  • Open circuit, short to positive or Ground in the wiring
 -- Check wiring and connections using wiring diagram
    -- Perform electrical checks ELECTRICAL TESTING 
    If the malfunction occurs again:
 
  • ABS Control Module -J104- faulty
 -- ABS Control Module -J104- (w/EDL)
    Removal and Installation
(1) Type of DTC; this DTC is only recognized above 20 km/h (13 MPH) (carry out test drive).
VAG 1551 print-out Possible cause Corrective action
01276    
ABS Hydraulic Pump -V64- Signal outside tolerances(1)
  • ABS Hydraulic Pump -V64- connector to control module faulty
 -- Perform output Diagnostic Test Mode (DTM) FUNCTION 03 - OUTPUT DIAGNOSTIC TEST MODE 
 
  • Open circuit, short to positive or Ground in the wiring
 -- Check wiring and connections using wiring diagram
    -- Perform electrical checks ELECTRICAL TESTING 
 
  • ABS Hydraulic Pump -V64- faulty
 -- If the ABS Hydraulic Pump -V64- runs free while electrical check test step 18 performed ELECTRICAL TEST TABLE => Checking CAN-bus wire  and ELECTRICAL TEST TABLE => Checking CAN-bus wire , replace ABS Hydraulic Pump -V64- (w/EDL)
 
  • ABS Control Module -J104- (w/EDL) faulty
 -- Replace ABS Control Module -J104- (w/EDL)
    Removal and Installation
(1) Type of DTC; this DTC is only recognized above 20 km/h (13 MPH) (carry out test drive).
VAG 1551 print-out Possible cause Corrective action
01312    
Drive train data bus faulty(1) or:
  • ABS Control Module -J104- (w/EDL) incorrectly coded
  • Engine control module incorrectly coded
 -- Check ABS Control Module -J104- (w/EDL)coding FUNCTION 07 - CODING CONTROL MODULE -- Check engine control module coding [For engine(s) ALH] Diagnosis and Testing
 
  • Open circuit, short to positive or Ground in the wiring
 -- Check wiring and connections using wiring diagram
    -- Perform electrical checks ELECTRICAL TESTING 
Drive train data bus faulty(1) Sporadic
  • Ignition/starter switch turned too slowly
 -- Erase DTC memory FUNCTION 05 - ERASING DTC MEMORY -- No further measures required-- Inform customer
(1) The DTC "Drive train data bus" will not cause the ABS Warning Lamp -K47- or Brake System Warning Lamp -K118- to light up. The ABS function is retained over the complete range.
VAG 1551 print-out Possible cause Corrective action
01314    
Engine control module No communication   -- Read measured value block FUNCTION 08 - READING MEASURED VALUE BLOCK  display group number 125
 
  • Open circuit, short to positive or Ground in data bus wiring
 -- Check wiring and connections of data bus wiring using wiring diagram
    -- Perform electrical checks ELECTRICAL TESTING 
01315    
Transmission Control Module (TCM)(1) No communication   -- Read measured value block FUNCTION 08 - READING MEASURED VALUE BLOCK  display group number 125
 
  • Open circuit, short to positive or Ground in data bus wiring
 -- Check wiring and connections of data bus wiring using wiring diagram
    -- Perform electrical checks ELECTRICAL TESTING 
(1) Vehicles with automatic transmission only.
VAG 1551 print-out Possible cause Corrective action
01316    
Brake control module No communication
  • Open circuit, short circuit to positive or Ground in data bus wiring
 -- Check data bus wiring and connection using wiring diagram
    -- Perform electrical checks ELECTRICAL TESTING 
VAG 1551 print-out Possible cause Corrective action
18256    
Check Engine Control Module (ECM) memory
  • DTC in ECM
 -- Check engine control module DTC memory
65535    
Control module faulty ABS Control Module -J104- (w/EDL) faulty -- Replace ABS Control Module -J104- (w/EDL)
    Removal and Installation


NOTE:

When beginning On Board Diagnostic (OBD) troubleshooting of the vehicle control modules, always start with function "Automatic test sequence" by pressing keys 0  and 0  because the control modules are interconnected with a data bus wire. This checks the DTC memories of the control modules in the vehicle.

All the possible DTCs which can be recognized by the ABS Control Module -J104- (w/EDL) and printed-out on Scan Tool VAG1551 or Vehicle Diagnostic Testing and Information System VAS5051, are listed on the following pages according to the 5 digit DTC code.

DTC code appears (in the "Rapid data transfer" mode) only on the print-out.

Example:    
DTC code P code DTC type code
5 digit 5 digit 3 digit
18256 P1848 035
VAG 1551 print-out Possible cause Repair
No DTC recognized If "No DTC recognized" appears after carrying out repairs, On Board Diagnostic (OBD) is ended.
  If, despite "No DTC recognized" appearing in the display, the ABS system does not function properly, then proceed as follows:
  1. Carry out road test exceeding 20 km/h (13 mph),
  2. Again check DTC memory, if there is still no DTC stored,
  3. Continue troubleshooting without OBD and work through the complete Electrical check ABS MARK 60, TESTING ELECTRICALLY .
0003    
Fault number: 0003 / literature ABS Control Module -J104- (w/EDL) faulty -- Replace ABS Control Module -J104- (w/EDL)
    Removal and Installation
VAG 1551 print-out Possible cause Repair
00283    
Left Front ABS Wheel Speed Sensor -G47- (1) Electrical malfunction in current circuit
  • Open circuit in wiring between Left Front ABS Wheel Speed Sensor -G47- -G47- and ABS Control Module -J104- (w/EDL)
 -- Check wiring and connections referring to wiring diagram-- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
    -- Read measured value block MEASURED VALUE BLOCK, READING  Display group number 001
    Removal and Installation
    If the malfunction occurs again:
 
  • Left Front ABS Wheel Speed Sensor -G47- faulty
 -- Replace Left Front ABS Wheel Speed Sensor -G47- Removal and Installation
(1) This DTC is recognized when vehicle is stationary.
VAG 1551 print-out Possible cause Repair
00283    
Left Front ABS Wheel Speed Sensor -G47- (1) Implausible signal
  • Open circuit or loose contact in wiring between Left Front ABS Wheel Speed Sensor -G47- and ABS Control Module -J104- (w/EDL)
 -- Check wiring and connections using wiring diagram
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • Electrical interferences from other sources (high frequency radiation e.g. uninsulated ignition cable)
 -- Read measured value block MEASURED VALUE BLOCK, READING  Display group number 001
(1) This DTC is only recognized above 20 km/h (13 mph) (carry out test drive).
VAG 1551 print-out Possible cause Repair
00283    
Left Front ABS Wheel Speed Sensor -G47- Mechanical fault(1)
  • Excessive air gap between Left Front ABS Wheel Speed Sensor -G47- and rotor (signal not OK.)
 -- Check installation position of Left Front ABS Wheel Speed Sensor -G47- and rotor. Removal and Installation
    -- Read measured value block MEASURED VALUE BLOCK, READING  Display group numbers 001 and 002
    -- Perform test drive
 
  • Short to positive or ground in wiring
 -- Check wiring and connections using wiring diagram
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • Left Front ABS Wheel Speed Sensor -G47- faulty
 -- Replace Left Front ABS Wheel Speed Sensor -G47- Removal and Installation
(1) This DTC is only recognized above 20 km/h (13 mph) (carry out test drive).
VAG 1551 print-out Possible cause Repair
00285    
Right Front ABS Wheel Speed Sensor -G45- (1) Electrical malfunction in current circuit
  • Open circuit in wiring between Right Front ABS Wheel Speed Sensor -G45- and ABS Control Module -J104- (w/EDL)
 -- Check wiring and connections using to wiring diagram-- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
    -- Read measured value block MEASURED VALUE BLOCK, READING  Display group number 001
    Removal and Installation
    If the malfunction occurs again:
 
  • Right Front ABS Wheel Speed Sensor -G45- faulty
 -- Replace Right Front ABS Wheel Speed Sensor -G45- Removal and Installation
(1) This malfunction is recognized when vehicle is stationary.
VAG 1551 print-out Possible cause Repair
00285    
Right Front ABS Wheel Speed Sensor -G45- (1) Implausible signal
  • Open circuit; short to ground or loose contact in wiring between Right Front ABS Wheel Speed Sensor -G45- and ABS Control Module -J104-
 -- Check wiring and connection using wiring diagram
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • Electrical interference from other sources (high frequency radiation e.g. uninsulated ignition cable)
 -- Read measured value block MEASURED VALUE BLOCK, READING  Display group number 001
(1) This DTC is only recognized above 20 km/h (13 mph) (carry out test drive).
VAG 1551 print-out Possible cause Repair
00285    
Right Front ABS Wheel Speed Sensor -G45- Mechanical malfunction(1)
  • Excessive air gap between Right Front ABS Wheel Speed Sensor -G45- and rotor (signal not OK.)
 -- Check installation position of Right Front ABS Wheel Speed Sensor -G45- and rotor. Removal and Installation
    -- Read measured value block MEASURED VALUE BLOCK, READING  Display group numbers 001 and 002
    -- Perform test drive
 
  • Short to positive or Ground in wiring
 -- Check wiring and connections using wiring diagram
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • Right Front ABS Wheel Speed Sensor -G45- faulty
 -- Replace Right Front ABS Wheel Speed Sensor -G45- Removal and Installation
(1) This DTC is only recognized above 20 km/h (13 mph) (carry out test drive).
VAG 1551 print-out Possible cause Repair
00287    
Right Rear ABS Wheel Speed Sensor -G44- (1) Electrical malfunction in current circuit
  • Open circuit in wiring between Right Rear ABS Wheel Speed Sensor -G44- and ABS Control Module -J104- (w/EDL)
 -- Check wiring and connections using wiring diagram-- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
    -- Read measured value block MEASURED VALUE BLOCK, READING  Display group number 001
    Removal and Installation
    If the malfunction occurs again:
 
  • Right Rear ABS Wheel Speed Sensor -G44- faulty
 -- Replace Right Rear ABS Wheel Speed Sensor -G44- Removal and Installation
(1) This malfunction is recognized when vehicle is stationary.
VAG 1551 print-out Possible cause Repair
00287    
Right Rear ABS Wheel Speed Sensor -G44- (1) Implausible signal
  • Open circuit; short to ground or loose contact in wiring between Right Rear ABS Wheel Speed Sensor -G44- and ABS Control Module -J104- (w/EDL)
 -- Check wiring and connections using wiring diagram
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • Electrical interference from other sources (high frequency radiation e.g. uninsulated ignition cable)
 -- Read measured value block MEASURED VALUE BLOCK, READING  Display group number 001
(1) This DTC is only recognized above 20 km/h (13 mph) (carry out test drive).
VAG 1551 print-out Possible cause Repair
00287    
Right Rear ABS Wheel Speed Sensor -G44- (1) Mechanical malfunction
  • Excessive air gap between Right Rear ABS Wheel Speed Sensor -G44- and rotor (signal not OK.)
 -- Check installation position of Right Rear ABS Wheel Speed Sensor -G44- and rotor. Removal and Installation
    -- Read measured value block MEASURED VALUE BLOCK, READING  Display group numbers 001 and 002
    -- Perform test drive
 
  • Short to positive or ground in wiring
 -- Check wiring and connections using wiring diagram
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • Right Rear ABS Wheel Speed Sensor -G44- faulty
 -- Replace Right Rear ABS Wheel Speed Sensor -G44- Removal and Installation
(1) This DTC is only recognized above 20 km/h (13 mph) (carry out test drive).
VAG 1551 print-out Possible cause Repair
00290    
Left Rear ABS Wheel Speed Sensor -G46- (1) Fault in electrical circuit
  • Open circuit; short to positive or ground, or loose contact in connections between Left Rear ABS Wheel Speed Sensor -G46- and ABS Control Module -J104- (w/EDL)
 -- Check wiring and connections using wiring diagram-- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
    -- Read measured value block MEASURED VALUE BLOCK, READING  Display group number 001
    Removal and Installation
    If the malfunction occurs again:
 
  • Left Rear ABS Wheel Speed Sensor -G46- faulty
 -- Replace Left Rear ABS Wheel Speed Sensor -G46- Removal and Installation
(1) This DTC is recognized when vehicle is stationary.
VAG 1551 print-out Possible cause Repair
00290    
Left Rear ABS Wheel Speed Sensor -G46- (1) Implausible signal
  • Open circuit; short to positive or ground, or loose contact in connections between Left Rear ABS Wheel Speed Sensor -G46- and ABS Control Module -J104- (w/EDL)
 -- Check wiring and connections using wiring diagram-- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • Electrical interference from other sources (high frequency radiation e.g. uninsulated ignition cable)
 -- Read measured value block MEASURED VALUE BLOCK, READING  Display group number 001
(1) This DTC is only recognized above 20 km/h (13 mph) (carry out test drive).
VAG 1551 print-out Possible cause Repair
00290    
Left Rear ABS Wheel Speed Sensor -G46- (1) Mechanical malfunction
  • Excessive gap between Left Rear ABS Wheel Speed Sensor -G46- and rotor (signal not OK)
 -- Check installation of Left Rear ABS Wheel Speed Sensor -G46- and rotor Removal and Installation
    -- Read measured value block MEASURED VALUE BLOCK, READING  Display group numbers 001 and 002
    -- Perform test drive
 
  • Short to positive or Ground in wiring
 -- Check wiring and connections using wiring diagram
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • Left Rear ABS Wheel Speed Sensor -G46- faulty
 -- Replace Left Rear ABS Wheel Speed Sensor -G46- Removal and Installation
(1) This DTC is only recognized above 20 km/h (13 mph) (carry out test drive).
VAG 1551 print-out Possible cause Repair
00493    
ESP-Sensor Unit, vehicles from my 12.01 No Signal/Communication or ESP-Sensor Unit faulty
  • Open circuit, short to positive or ground in data bus wiring
  • ESP Sensor Unit -G419- faulty
 -- Check wiring and connectors of data bus wiring using current flow diagram-- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY -- Replace ESP Sensor Unit -G419- Removal and Installation -- Perform a zero compensation:-- Initiate basic setting BASIC SETTING, INITIATING  Display group number 063
VAG 1551 print-out Possible cause Rectifying fault
00495    
ESP-Sensor Unit, vehicles from m.y. 12.01 Voltage supply
  • Open circuit, short to positive or ground in the wiring
 -- Check wiring and connections using current flow diagram. Refer to appropriate SYSTEM WIRING DIAGRAM
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
VAG 1551 print-out Possible cause Repair
00526    
Brake Light Switch -F- (1) Implausible signal
  • Open circuit, short to positive or ground in the wiring
 -- Read measured value block MEASURED VALUE BLOCK, READING  Display group number 002-- Check wiring and connections using wiring diagram
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • Brake light switch improperly adjusted
  • Brake light switch faulty
 -- Adjust brake light switch.
(1) With ABS/EDL/ASR/ESP only.
VAG 1551 print-out Possible cause Repair
00538    
Reference voltage Malfunction in electrical circuit
  • Short to positive or ground in wiring for voltage supply
  • Voltage supply is less than 5 Volt
  • Rotation Rate Sensor -G202-
  • Transverse Acceleration Sensor -G200-
  • Brake Pressure Sensor 1 -G201-
 -- Check wiring and connections referring to wiring diagram-- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
00668    
Vehicle voltage terminal 30 Implausible signal
  • Open circuit, short to positive or ground in the wiring
 -- Check wiring and connections using wiring diagram
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • Alternator voltage > 17 Volt
 Refer to appropriate SYSTEM WIRING DIAGRAM
VAG 1551 print-out Possible cause Repair
00778    
Steering Angle Sensor -G85- No signal/communication(1)
  • Open circuit or loose contact in data bus wiring between Steering Angle Sensor -G85- and ABS Control Module -J104- (w/EDL)
  • Terminal 15 and 30 on Steering Angle Sensor -G85-, Ground not present
 -- Check wiring and connections using wiring diagram
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • Steering Angle Sensor -G85- faulty
 -- Replace Steering Angle Sensor -G85-. Removal and Installation
    -- Perform a zero compensation. Initiating basic settings, BASIC SETTING, INITIATING  Display group number 060
(1) With ABS/EDL/ASR/ESP only.
VAG 1551 print-out Possible cause Repair
00778    
Steering Angle Sensor -G85- (1) Mechanical malfunction
  • Steering wheel has been removed and then no zero compensation has been performed.
 -- Perform a zero compensation. Initiating basic settings, BASIC SETTING, INITIATING  Display group number 060
 
  • Check specification from Steering Angle Sensor -G85-
 -- Read measured value block MEASURED VALUE BLOCK, READING  Display group number 004
 
  • Steering geometry of suspension is not OK.
 -- Check vehicle alignment. Description and Operation
 
  • Installation of Steering Angle Sensor -G85- is not OK
 -- Check installation of Steering Angle Sensor -G85-
 
  • Steering Angle Sensor -G85- faulty
 -- Replace Steering Angle Sensor -G85-. STEERING ANGLE SENSOR
(1) With ABS/EDL/ASR/ESP only.
VAG 1551 print-out Possible cause Repair
00778    
Steering Angle Sensor -G85- Implausible signal(1)
  • Installation of Steering Angle Sensor -G85- is not OK.
 -- Check installation of Steering Angle Sensor -G85-
    Removal and Installation
 
  • Steering geometry of suspension is not OK.
 -- Check vehicle alignment Description and Operation
 
  • Unacceptable vibrations in steering due to wear.
 -- Perform a zero compensation. Initiating basic settings, BASIC SETTING, INITIATING  Display group number 060
00778    
Steering Angle Sensor -G85- (1) No or incorrect basic settings / adaptation
  • Steering Angle Sensor -G85- sends no or incorrect setting values
 -- Perform a zero compensation. Initiating basic settings, BASIC SETTING, INITIATING  Display group number 060
(1) With ABS/EDL/ASR/ESP only.
VAG 1551 print-out Possible cause Repair
00778    
Steering Angle Sensor -G85- faulty(1)
  • Steering Angle Sensor -G85- faulty
 -- Replace Steering Angle Sensor -G85-
    Removal and Installation
    -- Perform a zero compensation. Initiating basic settings, BASIC SETTING, INITIATING  Display group number 060
01044    
Control module incorrectly coded
  • ABS Control Module -J104- (w/EDL) incorrectly coded
 -- Check coding for ABS Control Module -J104- (w/EDL) MEASURED VALUE BLOCK, READING 
 
  • Open circuit or short circuit in coding bridge in multi-pin connector to ABS Control Module -J104- (w/EDL)
 -- Check wiring and connections using wiring diagram. Refer to appropriate SYSTEM WIRING DIAGRAM
(1) With ABS/EDL/ASR/ESP only.
VAG 1551 print-out Possible cause Repair
01130    
ABS operation Implausible signal(1)
  • Electrical interference from other sources (high frequency radiation e.g. non-insulated ignition cable)
 -- Erase DTC memory-- Perform test drive at more than 20 km/h (13 mph)-- Check DTC memory again
 
  • Open circuit, short to positive or Ground in the wiring
 -- Check wiring and connections using wiring diagram
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • ABS Control Module -J104- (w/EDL) faulty
 -- Replace ABS Control Module -J104- (w/EDL). Removal and Installation
(1) This DTC is only recognized above 20 km/h (13 mph) (carry out test drive).
VAG 1551 print-out Possible cause Repair
01164    
ESP operation Implausible signal(1)
  • Electrical interferences from external interference sources (high frequency radiation, e.g. non-insulated ignition cable)
 -- Erase DTC memory-- Carry out a test drive exceeding 20 km/h (13 mph)-- Check DTC memory again
 
  • Open circuit, short to positive or ground in the wiring
 -- Check wiring and connections using wiring diagram
 
  • Steering Angle Sensor -G85- sends incorrect setting values
 -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY -- Perform a zero compensation:
 
  • ABS Control Module -J104- (w/EDL) faulty
 -- Replace ABS Control Module -J104- (w/EDL). Removal and Installation
(1) Type of DTC, this DTC is only recognized above 20 km/h (13 mph) (carry out test drive).
VAG 1551 print-out Possible cause Repair
01276    
ABS Hydraulic Pump -V64- Implausible signal(1)
  • Transfer resistance in Ground or positive wire
 -- Check wiring and connections using wiring diagram
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • ABS Hydraulic Pump -V64- faulty
 -- Replace ABS Hydraulic Pump -V64- Removal and Installation
01276    
ABS Hydraulic Pump -V64- faulty(1)
  • Short circuit in electronics
 -- Replace ABS Hydraulic Unit -N55- with ABS Control Module -J104- (w/EDL). Removal and Installation
(1) This DTC is only recognized above 20 km/h (13 mph) (carry out test drive).
VAG 1551 print-out Possible cause Repair
01276    
ABS hydraulic pump ABS Hydraulic Pump -V64- Electrical malfunction in current circuit (1)
  • Battery positive fuse faulty
 -- Check fuses
 
  • Open circuit, short to positive or Ground in the wiring
 -- Check wiring and connections using wiring diagram
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • ABS Hydraulic Pump -V64- faulty
 -- Replace ABS Hydraulic Unit -N55- Removal and Installation
(1) This DTC is only recognized above 20 km/h (13 mph) (carry out test drive).
VAG 1551 print-out Possible cause Repair
01312    
Drive train data bus faulty(1)   -- Read measured value block MEASURED VALUE BLOCK, READING , Display group number 125
 
  • Open circuit, short to positive or Ground in data bus wiring
 -- Check wiring and connections of data bus wiring using wiring diagram
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
(1) This DTC only occurs together with DTC:"Steering angler sensor -G85-, No communication".
VAG 1551 print-out Possible cause Repair
01314    
Engine control module No signal/communication   -- Read measured value block MEASURED VALUE BLOCK, READING  Display group number 125
 
  • Open circuit, short to positive or Ground in data bus wiring
 -- Check wiring and connections of data bus wiring using wiring diagram
or:    
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
Check DTC memory
  • DTC entry in engine control module
 -- Check DTC memory of engine control module: [For engine(s) APH, BNU, AWP, AWV, BKF] Diagnosis and Testing or to [For engine(s) BPR, BPS] Diagnosis and Testing or to [For engine(s) BDC, BEV, BGD, AVH, AZG, AEG] Diagnosis and Testing
VAG 1551 print-out Possible cause Repair
01315    
Transmission control module(1) No signal/communication   -- Read measured value block MEASURED VALUE BLOCK, READING  Display group number 125
 
  • Open circuit, short to positive or Ground in data bus wiring
 -- Check wiring and connections of data bus wiring using wiring diagram
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
01317    
Instrument Cluster Control Module -J285-
  • Instrument Cluster Control Module -J285- - incorrectly coded
 -- Check Instrument Cluster Control Module -J285- coding. Diagnosis and Testing
(1) Vehicles with an automatic Transmission only
VAG 1551 print-out Possible cause Repair
01423    
Transverse Acceleration Sensor -G200- (1) Electrical malfunction in current circuit
  • Check connections
  • Voltage supply less than 5 Volt
  
 
  • Open circuit, short to positive or Ground in the wiring
 -- Check wiring and connections referring to wiring diagram
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • Transverse Acceleration Sensor -G200- faulty
 -- Replace Transverse Acceleration Sensor -G200-. Removal and Installation
    -- Perform a zero compensation. Initiating basic settings, BASIC SETTING, INITIATING  Display group number 063
(1) With ABS/EDL/ASR/ESP only.
VAG 1551 print-out Possible cause Repair
01423    
Transverse Acceleration Sensor -G200- Implausible signal(1)   -- Read measured value block MEASURED VALUE BLOCK, READING  Display group number 004
 
  • The installation position of sensor for transverse acceleration -G200- is not OK.
 -- Check installation position of Transverse Acceleration Sensor -G200-.
 
  • Open circuit, short to positive or Ground in the wiring
 -- Check wiring and connections using wiring diagram-- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • Transverse Acceleration Sensor -G200- faulty
 -- Replace Transverse Acceleration Sensor -G200-. Removal and Installation
 
  • Basic settings was not performed correctly in the past
 -- Perform a zero compensation. Initiating basic settings, BASIC SETTING, INITIATING  Display group number 063
(1) With ABS/EDL/ASR/ESP only.
VAG 1551 print-out Possible cause Repair
01423    
Transverse Acceleration Sensor -G200- (1) No or incorrect basic settings / adaptation
  • A zero compensation has never been performed.
 -- Perform a zero compensation. Initiating basic settings, BASIC SETTING, INITIATING  Display group number 063
01435    
Brake Pressure Sensor 1 -G201- No or incorrect basic settings / adaptation (1)
  • A zero compensation has never been performed.
 -- Perform a zero compensation. Initiating basic settings, BASIC SETTING, INITIATING  Display group number 066
(1) With ABS/EDL/ASR/ESP only.
VAG 1551 print-out Possible cause Repair
01435    
Brake Pressure Sensor 1 -G201- Implausible signal(1)   -- Read measured value block MEASURED VALUE BLOCK, READING  Display group number 005
 
  • Open circuit, short to positive or Ground in the wiring
 -- Check wiring and connections using wiring diagram-- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • Brake light switch improperly adjusted
  • Brake light switch faulty
 -- Adjust brake light switch.
 
  • Sender 1 for brake booster -G201- faulty
 -- Replace Brake Pressure Sensor 1 -G201- Removal and Installation
    -- Perform a zero compensation. Initiating basic settings, BASIC SETTING, INITIATING  Display group number 066
(1) With ABS/EDL/ASR/ESP only.
VAG 1551 print-out Possible cause Repair
01435    
Brake Pressure Sensor 1 -G201- Electrical malfunction in current circuit(1)
  • Connections
  • Voltage supply is less than 5 Volt
  
 
  • Open circuit, short to positive or ground in the wiring
 -- Check wiring and connections using wiring diagram
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • Sender 1 for brake booster 1 -G201- faulty
 -- Replace Brake Pressure Sensor 1 -G201- Removal and Installation
    -- Perform a zero compensation. Initiating basic settings, BASIC SETTING, INITIATING  Display group number 066
(1) With ABS/EDL/ASR/ESP only.
VAG 1551 print-out Possible cause Repair
01486 / literature(1)    
 
  • The ESP driving test is activated
 -- Perform the complete ESP driving test; the DTC will be erased automatically
    -- Initiate basic setting BASIC SETTING, INITIATING  Display group number 093
01487 / literature(1)    
 
  • The ESP driving test time has been exceeded
 -- Perform the complete ESP driving test within the allowed time
(1) With ABS/EDL/ASR/ESP only.
VAG 1551 print-out Possible cause Repair
01542    
Rotation Rate Sensor -G202- Implausible signal (1)   -- Read measured value block MEASURED VALUE BLOCK, READING  Display group number 004
 
  • Installation of Rotation Rate Sensor -G202- is not OK.
 -- Check installation of Rotation Rate Sensor -G202-
 
  • Open circuit, short to positive or ground in the wiring
 -- Check wiring and connections using wiring diagram-- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • Rotation Rate Sensor -G202- faulty
 -- Replace Rotation Rate Sensor -G202- : Removal and Installation
(1) With ABS/EDL/ASR/ESP only.
VAG 1551 print-out Possible cause Repair
01542    
Rotation Rate Sensor -G202- (1) Electrical malfunction in current circuit
  • Connections
  • Voltage supply is less than 5 Volt
  
 
  • Open circuit, short to positive or Ground in the wiring
 -- Check wiring and connections using wiring diagram
    -- Perform electrical check → from ABS MARK 60, TESTING ELECTRICALLY 
 
  • Rotation Rate Sensor -G202- faulty
 -- Replace Rotation Rate Sensor -G202-. Removal and Installation
(1) With ABS/EDL/ASR/ESP only.
scientia non olet · About LEMON Manuals